fbpx

Tube Distortion In Vital – A How to Guide

Veteran users of Xfer’s long standing giant Serum (to which Vital is often compared) will no doubt quickly notice a distinct lack of any kind of “Tube” or “Tape” style algorithms in the built in distortion module. 

These kinds of algorithms are integral to many bass design techniques, and the simple clipping or more exotic folding and degradation algorithms on offer are in many cases no substitute. 

Fortunately, there are a couple of effective workarounds. 

Method One – Filter Drive

The “Drive” algorithms available on the three configurable filters are lovely for adding that gritty warmth that we’re after, but they need some setup to get it cleanly.

The two main panel’s filters are “Polyphonic” filters, that is to say that each voice is given it’s own unique instance of the filter.

This allows Vital to key-track individual voices separately, as well as distort each voice separately, avoiding the potentially inharmonic inter-modulation from distorting two notes together.

However, that inter-modulation potential is sometimes an important part of what we want out of our distortion, which is where the third filter comes in. 

The filter in the FX section of Vital is “Monophonic”, which is to say that there’s only one copy of it and all the notes you play go through the same filter.

By taking advantage of its drive knob, we’re given the opportunity for intermodulation and that warmer, more unpredictable analog sounding distortion we’re after.

A visual example of Polyphonic VS Monophonic Filters

For a filter shape that minimally affects the tone of your sound, so that you can distort without removing any frequencies, follow these steps:

  1. Select the “B/P/N” mode of whichever filter type you prefer
  2. Turn the resonance all the way down
  3. Adjust the “Blend” Control above the colored display until the curve mostly flattens out – a value of around 1.3 works for most of them, and the ladder is totally flat at 1.0!
  4. Adjust the “Drive” knob on the filter to taste!

Best of all, this technique can be combined with the distortion module for even more sonic destruction! 

This is what the end result will look like.

Once you have this setup, just adjust the drive knob to add distortion!

– BONUS TIP #1 –

Speaking of key-tracking, the “Note Priority” setting under the “Voice” section of the “Advanced” tab determines which note “wins” when key-tracking is enabled on a monophonic target (like the filter in the FX section) and multiple notes are played at once.

You can select between “Newest”, “Oldest”, “Highest”, “Lowest”, and “Round Robin”, to various effects. 

Method Two – Parallel Distortion Filtering

Another way to get some warmer distortion out of the distortion module itself is through parallel distortion and filtering.

Here’s the rundown:

  1. Engage the filter on the distortion module by selecting “Post” or “Pre”. (Make sure to try both – since distortion is a nonlinear operation, they’ll sound different.)
  2. Then adjust the filter shape using the cutoff, resonance and blend knobs to dial in a nice, low, resonant low pass filter.
  3. Adjust the drive and filter shape until you like the harmonics you’re hearing.
  4. Now dial down the mix knob to bring back some of the original signal including pristine, undistorted high end. (This use of the mix control to combine the dry and wet signals is what’s meant by “parallel” in “parallel distortion” or “parallel compression”.)

This is what the end result will look like.

Once you have this setup, just adjust each of the settings from each step to taste!

You can often drive this kind of distortion fairly hard, especially when “pre” is selected, because the typical intermodulation between the fundamental (first harmonic, lowest frequency and root of the perceived pitch) of the note and its harmonic overtones won’t be present since those overtones will get filtered out before arriving at the distortion.

Instead, you just get a bunch of harmonics related to your fundamental, which sound lovely!

– Bonus Tip #2 –

If you want, you can even keytrack the cutoff of the distortion filter using the “Note” modulator in the bottom right of Vital’s UI, for an interesting tone which can sound more consistent across the keyboard. 

Wrap Up

You can use two methods to achieve a tube-like distortion effect inside of Vital:

  • Utilizing filter drive
  • By using parallel distortion filtering

By using these two workarounds, you’ll now be able to emulate tube distortion inside of Vital!

CREATE POWERFUL AND EMOTIONAL MUSIC WITH

Odyssey

MELODIC DUBSTEP FOR VITAL

FIND YOUR SOUND
Our site uses cookies to improve your experience. By using this website, you agree to our use of cookies.